| Teil no | Hersteller | Application |
|---|
| MAX1109CUB | MAXIMIC | Single-supply, low-power, 2-channel, serial 8-bit ADC |
| MAX4074BCESA | MAXIMIC | Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 15V/V, noniverting gain 16.5V/V, -3dB BW 54kHZ. |
| MAX6316MUK29CY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,standard version (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 2.930V, min reset timeout 140ms,typ watchdog timeout 1.6sec |
| MAX1480CEPI | MAXIMIC | Complete, isolated RS-485/RS-422 data inteface. |
| MAX478CPA | MAXIMIC | 17microA max, dual, single-supply, precision op amp. |
| MAX2470EUT-T | MAXIMIC | 10 MHz to 500 MHz VCO buffer amplifier with differential outputs. |
| MAX6380UR36-T | MAXIMIC | Ultra-low-power voltage detector, 3.6V |
| MAX6363PUT44-T | MAXIMIC | Low-power microprocessor supervisory circuit with battery-on output. Reset threshold(typ) 4.38V. Active-low open-drain reset. |
| DG384C/D | MAXIMIC | General purpose CMOS dual analog switch. |
| MAX6318MHUK44BY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX4428C/D | MAXIMIC | Dual high-speed, 1.5A MOSFET driver. 4.5V t0 18V operation range. |
| MAX239CNG | MAXIMIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX495C/D | MAXIMIC | Single, micropower, single-supply operation (+2.7V to +6V), Rail-to-Rail op amp. |
| MAX6319LHUK27C-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 140ms |
| MAX4074AHESA | MAXIMIC | Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 2.5V/V, noninverting gain 3.5V/V, -3dB BW 116kHZ. |
| MAX305MLP | MAXIMIC | Precision, dual, high-speed analog switch. |
| MX584KH | MAXIMIC | Pin programmable precision voltage reference. Error +-10mV. |
| MAX353EJE | MAXIMIC | Precision, quad, SPST analog switch |
| MAX6322HPUK48B-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.800V, reset timeout(min) 20ms |
| MAX491EESD | MAXIMIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Full-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MX7575BQ | MAXIMIC | CMOS, microprocessor-compatible, fast conversion time 5 microsec, 8-bit ADC. INL +-1/2 LSB. |
| MAX6316MUK44BX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.390V, min reset timeout 20ms, typ watchdog timeout 102ms |
| DG421CY | MAXIMIC | Improved low-pover, CMOS analog switches with latches |
| MAX802RESA | MAXIMIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.625V. Active-low reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX384CPN | MAXIMIC | Low-voltage, dual 4-channel multiplexer with latchable inputs. |
| MAX754CPE | MAXIMIC | CCFL backlight and LCD contrast controller. Positive LCD contrast. |
| MAX843ESA | MAXIMIC | Low-noise, regulated, -2V GaAsFET bias. 1microA max logic-level shutdown over temp. |
| MAX6336US17D1-T | MAXIMIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, push/pull . Reset threshold(typ) 1.7V, reset timeout(min) 1ms. |
| MAX249CQH | MAXIMIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX6316MUK25CZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 2.500V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
