| Teil no | Hersteller | Application |
|---|
| MAX6316LUK38DX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.800V, min reset timeout 1.12sec, typ watchdog timeout 102ms |
| MAX423CPD | MAXIMIC | +-15V chopper stabilized operational amplifier. |
| MAX4444ESE | MAXIMIC | Ultra-high-speed, low-distortion, differential-to-single-ended line receiver with enable. |
| MAX794ESE | MAXIMIC | Microprocessor supervisory circuit. Reset threshold programmable. Active-low reset.Active-high reset.Low-line early warning output.Backup-battery switchover.External switch driver.Power-fail comparator.Watchdog input.Manual reset inp. |
| MAX485EPA | MAXIMIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX664EPA | MAXIMIC | Dual Mode 5V or programmable micropower voltage negative regulator. |
| DG441DY | MAXIMIC | Improved, quad, SPST analog switch |
| MAX4391CPA | MAXIMIC | CMOS micropower inverting switching regulator |
| MAX887HESA | MAXIMIC | 100% duty cycle, low-noise, stet-down, PWM DC-DC converter. |
| MX7533UD | MAXIMIC | CMOS low-cost 10 bit multiplying D/A converter. Error 0.05% |
| MAX3086CSD | MAXIMIC | Fail-safe, high-speed (10Mbps), slew-rate-limited RS-485/RS-422 transceiver |
| MAX820TCPE | MAXIMIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 3.06V. Reset and low-line threshold accuracy +-2% |
| MAX4521CSE | MAXIMIC | Quad, low-voltage, SPST analog switch. |
| MAX3491CPD | MAXIMIC | 3.3V-powered, 10Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 10Mbps. Supply voltage 3.0V to 3.6V |
| MAX147BMJP | MAXIMIC | +2.7 V, low-power, 8-channel, serial 12-bit ADC. INL(LSB) +-1. |
| MAX6306UK25D4-T | MAXIMIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 2.438(min),2.563(max) Nominal timeout period 1120ms. |
| MAX6319MHUK30D-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 1120ms |
| MAX6316LUK36BX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.600V, min reset timeout 20ms, typ watchdog timeout 102ms |
| MAX4104EUK-T | MAXIMIC | Low-noise, low-distortion op amp. Bandwidth 625MHz. Minimum stable gain 1V/V. |
| MAX6336US25D3-T | MAXIMIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, push/pull . Reset threshold(typ) 2.5V, reset timeout(min) 100ms. |
| MAX688EPA | MAXIMIC | High-accuracy, low-dropout linear regulator |
| MAX6318LHUK27AZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.700V min, reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX4174BMEUK-T | MAXIMIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 80, 1+ (Rf/Dg) noninverting gain 81, -3dB BW 260kHz. |
| MAX136CPL | MAXIMIC | Low power, 3 1/2 didit A/D converter with display hold |
| MX7536KP | MAXIMIC | Microprocessor-compatible, 14-bit D/A converter. Accuracy +-1 LSB. |
| MAX704TCSA | MAXIMIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 3.075V. Active-low reset. Manual reset input. Backup-battery switch. Power-fail threshold accuracy +-4%. Power-fail comparator. Reset window +-75mV |
| MX7535TD | MAXIMIC | Microprocessor-compatible, 14-bit DAC. INL +-1 LSB. |
| MAX6321HPUK25BY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX1481CUB | MAXIMIC | Software-selectable, half-/full-duplex, slew-rate-limite 12 Mbps, RS-485/RS-422 transceiver. |
| MAX6318LHUK37CY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.700V min, reset timeout 140ms,typ watchdog timeout 1.6sec |
