| Teil no | Hersteller | Application |
|---|
| ICL7642CCPD | MAXIMIC | Quad operational amplifier, 10mV |
| MAX708SCUA | MAXIMIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 2.93V. Active-low and active-high reset output signal. |
| MX7542AQ | MAXIMIC | CMOS microprocessor-compatible 12 bit DAC. Error +1 LSB. |
| MAX805LESA | MAXIMIC | Microprocessor supervisory circuit. 4.65V precision supply-voltage monitor |
| MAX6316LUK28AZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX630MJA | MAXIMIC | CMOS micropower step-up switching regulator |
| MAX6316LUK26AX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.630V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX312EUE | MAXIMIC | 10Om, quad, SPST, CMOS analog switch |
| MAX6316LUK28AY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| MAX4016ESA | MAXIMIC | Low-cost, high-speed, single-supply op amp with Rail-to-Rail outputs. High speed 150MHz - 3dB bandwidth. Transistor count 190 . |
| MAX6309UK47D1-T | MAXIMIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 4.583(min),4.818(max) Nominal timeout period 1ms. |
| MAX4275ALEUA | MAXIMIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 5, 1+ (Rf/Dg) noninverting gain 6, -3dB BW 790kHz. |
| MAX396MJI | MAXIMIC | Precision, 16-channel, low-voltage, CMOS analo0g multiplexer. |
| MAX6316LUK36BW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.600V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX5465EXT | MAXIMIC | 2-wire digital potentiometer, 50KOm |
| MAX1627C/D | MAXIMIC | Adjustable, 100% duty-cycle, high-efficiency, step-down DC-DC controller |
| ICM7225IPL | MAXIMIC | 4-1/2 digit counter |
| MAX236CWG | MAXIMIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX953MJA | MAXIMIC | Ultra low-power, single-supply Op Amp + comparator. Op Amp gain stability 1V/V. Supply current 5microA. |
| MX7534TD | MAXIMIC | Microprocessor-compatible, 14-bit DAC. INL +-1 LSB. |
| MAX6319MHUK46A-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.630V, reset timeout(min) 1ms |
| MAX535BCPA | MAXIMIC | Low-power, 13-bit voltage-output DAC with serial interface. INL (LSB) +-1. +5V single-supply operation. |
| MAX819MEPA | MAXIMIC | +5V microprocessor supervisory circuit. Reset threshold 4.40V, active-low reset, backup-battery switchover, power-fail comparator, battery freshness seal, manual reset input. |
| MAX6318LHUK35BZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.500V min, reset timeout 20ms,typ watchdog timeout 25.6sec |
| MAX7645BMJP | MAXIMIC | TTL/CMOS compatible for Vdd = 15V, 12-bit buffered multiplying DAC. Gain error +-3 LSB. |
| MAX5154ACPE | MAXIMIC | Low-power, dual, 12-bit voltage-output DAC with serial interface. +5V single-supply operation. INL(LSB) +-1/2. |
| MAX6318LHUK28BY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.800V min, reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX247EPL | MAXIMIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX702ESA | MAXIMIC | Power-supply monitor with reset. |
| MAX6307UK46D3-T | MAXIMIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds4.514(min),4.746(max).Nominal timeout period 140ms. |
