| Teil no | Hersteller | Application |
|---|
| OP37EP | MAXIMIC | Low-noise precision operational amplifier. 63MHz gain-bandwidth product. 17V/micros slew rate. |
| MAX1295ACEI | MAXIMIC | 265ksps, +3V, 6-channel single-ended/3-channel pseudo-differential, 12-bit ADC with +2.5V reference and parallel interface INL(LSB) +0.5, -0.5 |
| IH5043CPE | MAXIMIC | General-purpose CMOS analog switch. Dual, single pole, double throw (Dual SPDT) |
| MAX6321HPUK29DZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX6318MHUK47AY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.700V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec |
| MAX4623CPE | MAXIMIC | Low on-resistance 3om(typ), 5om(max), dual, DBST, NO analog switch. |
| MX581JESA | MAXIMIC | High precision 10 volt reference. Error +-30mV. |
| MAX6316MUK44AY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.390V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| MAX6318LHUK46BY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.630V min, reset timeout 20ms,typ watchdog timeout 1.6sec |
| MAX506BEPP | MAXIMIC | Quad 8-bit DAC with Rail-to-Rail voltage outputs. Separate input latches for each of its four DACs. TUE +-3/2 LSB. |
| MAX708TESA | MAXIMIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 3.08V. Active-low and active-high reset output signal. |
| MAX6318MHUK39DZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| REF01EJ | MAXIMIC | +10V precisioon voltage reference. Max TEMPCO 8.5ppm/degC. Initial error +-30mV |
| MAX6320PUK28AZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.800V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX243CSE | MAXIMIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX934EPE | MAXIMIC | Quad low-power, low-cost comparator with intarnal 1.182V+-2% bandgap reference. |
| REF01J | MAXIMIC | +10V precisioon voltage reference. Max TEMPCO 25ppm/degC. Initial error +-50mV |
| MAX6334UR18D2-T | MAXIMIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 1.8V, reset timeout(min) 20ms. |
| MAX807LMJE | MAXIMIC | Full-featured microprocessor supervisory circuit with +-1.5% reset accuracy. Reset threshold (typ) 4.675V |
| MAX412CSA | MAXIMIC | Dual, 28MHz, low-noise, low-voltage, precision op amp. |
| MAX6320PUK34AY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.400V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec |
| MAX6318MHUK48BX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.800V, reset timeout(min) 20ms, watchdog timeout(typ) 102ms |
| MAX490ECPA | MAXIMIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Full-duplex. Data rate 2.5Mbps. Slew-rate limited - n0. Low-power shutdown - no. Receiver/driver enable - no. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX533AMJE | MAXIMIC | 2.7V, low-power, 8-bit quad DAC with Rail-to-Rail output buffer. INL (LSB) +-1 |
| MAX6319LHUK39C-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 140ms |
| MAX782RCBX | MAXIMIC | Triple-output power-supply controller for notebook computer. Vout 3.45V |
| MAX690AESA | MAXIMIC | Microprocessor supervisory circuit. 4.65V precision supply-voltage monitor |
| MAX6316LUK41AZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.100V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX160EWN | MAXIMIC | Microprocessor compatible 8-bit A/D converter. Fast conversion time 4microsec. Error +-1/2 LSB. |
| MAX458CPL | MAXIMIC | 8 x 4 video crosspoint switch with buffers |
