| Teil no | Hersteller | Application |
|---|
| MAX6322HPUK39C-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 140ms |
| MAX294EPA | MaximIC | 8th-order, lowpass, elliptic, switched-capacitor filter. Clock-tunable corner-freguency range 0.1Hz to 25kHz |
| MXD1013SA075 | MaximIC | 3-in-1 silicon delay line. Output delay 75ns. |
| MAX213EEWI | MaximIC | +-15kV ESD-protected, +5V RS-232 transceiver |
| MAX248CQH | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX365CSE | MaximIC | Precision, quad, SPST, normally open (NO) analog switch. |
| MX3554AM | MaximIC | Wideband fast-settling operational amplifier |
| ICL7650BCSD | MaximIC | Chopper-stabilized amplifier |
| IH5043C/D | MaximIC | General-purpose CMOS analog switch. Dual, single pole, double throw (Dual SPDT) |
| MAX4578CWP | MaximIC | High-voltage, single 8-to-1 cal-multiplexer. |
| MAX1771C/D | MaximIC | 12V or adjustable, high efficiency, low current, step-up DC-DC controller. |
| MAX1406EAE | MaximIC | +-15V, ESD-protected, EMC-compliant, 230kbps, 3-Tx/3-Rx RS-232 IC. |
| MAX6321HPUK39CX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX6318LHUK28BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.800V min, reset timeout 20ms, typ watchdog timeout 25.6sec |
| IH5352EPE | MaximIC | Quad RF and video switch |
| MAX452CPA | MaximIC | CMOS unity-gain stable, 50MHz video amplifier. |
| MAX6316LUK50AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 5.000V, min reser timeout 1ms, typ watchdog timeout 102ms. |
| MX7576KN | MaximIC | CMOS, microprocessor-compatible, fast conversion time 10 microsec, 8-bit ADC. INL +-1/2 LSB. |
| MAX810REXR-T10 | MaximIC | Microprocessor reset circuit. Reset threshold 2.63V. Push-pull active-high reset. 10k increments. |
| MAX6318MHUK27CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MX7530LQ | MaximIC | CMOS 10 bit multiplying D/A converter. Error 0.05% |
| MX7502SQ | MaximIC | Low-power, monolithic, CMOS analog multiplexer. |
| MAX327EPE | MaximIC | Quad, SPTS, ultra-low leakage, CMOS analog switch. |
| MAX530BEWG | MaximIC | +5V, low-power, parallel-input, voltage-output, 12-bit DAC. Error +-1. |
| MAX188DCCP | MaximIC | Low-power, 8-channel, serial 12-bit ADC. |
| MAX391ESE | MaximIC | Precision, quad, SPST analog switch |
| MAX4275AKESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 4, 1+ (Rf/Dg) noninverting gain 5, -3dB BW 970kHz. |
| MAX6320PUK41CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec |
| MAX6318LHUK45AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.500V min, reset timeout 1ms,typ watchdog timeout 6.3ms |
| MX7228KP | MaximIC | CMOS octal 8-bit D/A converter. Error +-2 LSB |
