| Teil no | Hersteller | Application |
|---|
| DG425CY | MAXIMIC | Improved low-pover, CMOS analog switches with latches |
| MAX873BMJA | MAXIMIC | Low-power, low-drift precision voltage reference. 2.5V+-2.5mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC. |
| MAX485CPA | MAXIMIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX6320PUK27CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX502BENG | MAXIMIC | Voltage-output, 12-bit multiplying DAC. Error(LSBs) +-3/4. |
| MAX4519MJD | MAXIMIC | Precision, dual 2-channel, low-voltage, CMOS analog multiplexer. Single-supply operation (+2.2V to +15V) or bipolar-supply operation (+-2.2V to +-8V). |
| MAX4598CWP | MAXIMIC | Low-voltage, CMOS analog IC, combination single-ended 8-to-1/differential 4-to-1 multiplexer. |
| MAX6316LUK41AX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.100V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX4220ESD | MAXIMIC | Quad, miniature, 200MHz -3dB bandwidth, single 3.3V/5.0V operation, Rail-to-Rail op amp with enable. |
| MAX906C/D | MAXIMIC | Dual, high-speed, positive edge-triggered, ECL-compatioble voltage comparator. |
| MX7547UQ | MAXIMIC | CMOS parallel loading dual 12 bit multiplying D/A converter. Gain error +-2 LSB. |
| MAX4174AHEUK-T | MAXIMIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 2.5, 1+ (Rf/Dg) noninverting gain 3.5, -3dB BW 820kHz. |
| MAX2267E/D | MAXIMIC | 2.7V, single-supply, cellular-band linear power amplifier. Low average CDMA current consumption in typical urban scenario 55mA. TSSOP-EP 5mm x 6.4mm. |
| MAX230CWP | MAXIMIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX829C/D | MAXIMIC | Switched-capacitor voltage inverter. 35kHz. +1.5V to +5.5V input voltage range. |
| MAX6316LUK33CW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low push/pull). Factory-trimmed reset threshold(typ) 3.300 ,min reset timeout 140ms,typ watchdog timeout 6.3ms |
| MAX6310UK31D4-T | MAXIMIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.003(min),3.157(max). Nominal timeout period 1120ms. |
| MAX6346XR45-T | MAXIMIC | Microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 4.500V. Order increment 10k |
| MAX8212ETY | MAXIMIC | Microprocessor voltage monitor with programmable voltage detection. High output current capability. |
| MAX6322HPUK45D-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 1120ms |
| MX7543SQ | MAXIMIC | CMOS serial input 12 bit DAC. Error +1 LSB. |
| MAX803ZEXR-T10 | MAXIMIC | Microprocessor reset circuit Reset threshold 2.32V. Open-drain active-low reset. 10k increments. |
| MAX6310UK48D2-T | MAXIMIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 4.680(min),4.920(max). Nominal timeout period 20ms. |
| MAX6711LEXS-T10 | MAXIMIC | Microprocessor reset circuit with manual reset input. Reset threshold 4.63V. Output type active-low push-pull reset. |
| MAX6318MHUK25DW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 1.12sec, watchdog timeout(typ) 6.3ms |
| MAX4174AKEUK-T | MAXIMIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 4, 1+ (Rf/Dg) noninverting gain 5, -3dB BW 970kHz. |
| MAX414BEPD | MAXIMIC | Quad, 28MHz, low-noise, low-voltage, precision op amp. |
| MAX704CSA | MAXIMIC | Low-cost microprocessor supervisory circuit with battery backup. Precison supply-voltage monitor 4.40V. |
| MAX876BEPA | MAXIMIC | Low-power, low-drift precision voltage reference. 10V+-5.0mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC. |
| MAX6318MHUK44CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
