| Teil no | Hersteller | Application |
|---|
| MAX1693EUB | MAXIMIC | USB current-limited switch with fault blanking |
| MAX521BC/D | MAXIMIC | Octal, 2-wire serial 8-bit DAC with Rail-to-Rail, unbuffered outputs. TUE(LSB) 2. |
| MAX509BC/D | MAXIMIC | Quad, serial 8-bit DAS with Rail-to-Rail output. TUE (LSB) +-1 1/2 |
| MAX6318LHUK28DX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.800V min, reset timeout 1.12sec, typ watchdog timeout 102ms |
| MAX4391C/D | MAXIMIC | CMOS micropower inverting switching regulator |
| MAX6316MUK28AZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX110BEWE | MAXIMIC | Low-cost, 2-channel, 14-bit serial ADC. |
| MAX327ESE | MAXIMIC | Quad, SPTS, ultra-low leakage, CMOS analog switch. |
| MAX110BEAP | MAXIMIC | Low-cost, 2-channel, 14-bit serial ADC. |
| MAX4131ESA | MAXIMIC | Single, wide-bandwidth, low-power, +2.7V to +6.5V single-supply operation, Rail-to-Rail I/O op amp. 25microA shutdown function. |
| DS1859B-050 | MAXIMIC | Dual, temperature-controlled resistors with internally calibrated monitors, 50KOhm |
| MAX3120CUA | MAXIMIC | Low-profile, 3V, 120microA, IrDA infrared transceiver. |
| MAX6320PUK45CZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX542BCPD | MAXIMIC | +5V,serial-input, voltage-output, 16-bit DAC. INL (LSB) +-2 |
| MAX320MJA | MAXIMIC | Precision, dual-supply, SPTS analog switch. |
| MAX490CPA | MAXIMIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - no. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| DG308ACK | MAXIMIC | Quad, SPST, NO analog switch |
| MAX6346XR33-T | MAXIMIC | Microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 3.300V. Order increment 10k |
| MAX1204BCAP | MAXIMIC | +5V, 8-channel, serial, 10-bit ADC with 3V digital interface, INL (LSB) +1 |
| MAX6318MHUK31BX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.080V, reset timeout(min) 20ms, watchdog timeout(typ) 102ms |
| MXL1001ACJ8 | MAXIMIC | Precision operational amplifier |
| DG412CJ | MAXIMIC | Improved, quad, SPST analog switches |
| MAX6309UK26D4-T | MAXIMIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 2.564(min),2.696(max) Nominal timeout period 1120ms. |
| MAX6321HPUK31DZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.080V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX6317HUK32AX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.200V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX6320PUK38AZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.800V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX6317HUK44AZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.390V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX6316MUK48CW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX164BEWG | MAXIMIC | CMOS 12-bit A/D converter with track-and-hold. Error +-1 LSB. |
| REF01HP | MAXIMIC | +10V precisioon voltage reference. Max TEMPCO 25ppm/degC. Initial error +-50mV |
