| Teil no | Hersteller | Application |
|---|
| MAX214C/D | MAXIMIC | Programmable DTE/DCE, +5V RS-232 transceiver. |
| MAX703EPA | MAXIMIC | Low-cost microprocessor supervisory circuit with battery backup. Precison supply-voltage monitor 4.65V. |
| MAX693AMJE | MAXIMIC | Microprocessor supervisory circuit. Reset threshold(typ) 4.4V. |
| MAX500AMLP | MAXIMIC | CMOS, quad, serial-interface 8-bit DAC. Error(LSB) +-1. |
| MAX529CPP | MAXIMIC | Octal, 8-bit, serial DAC with output buffer. Single +5V or dual +-5V supply operation. |
| MAX875BCPA | MAXIMIC | Low-power, low-drift precision voltage reference. 5V+-3.0mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC. |
| MAX488CPA | MAXIMIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - no. Receiver/driver enable - no. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| MAX6321HPUK34CZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.400V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MXL1016MJ8 | MAXIMIC | Ultra-fast precision TTL comparator. 10ns typ high-speed. |
| TSC428CPA | MAXIMIC | Dual power MOSFET driver contains one inverting and one non-inverting section. |
| MAX6320PUK40CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.000V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX197BCNI | MAXIMIC | Multi-range (+10V, +5V, +10V, +5V), single +5V, 12-bit DAS with 8+4 bus interface |
| MAX875BEPA | MAXIMIC | Low-power, low-drift precision voltage reference. 5V+-3.0mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC. |
| MAX6354MTUT-T | MAXIMIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.38V (Vcc5) and 3.08V (Vcc3). Active-low push-pull reset 3V. |
| MAX6321HPUK45CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX4428CPA | MAXIMIC | Dual high-speed, 1.5A MOSFET driver. 4.5V t0 18V operation range. |
| DG423DY | MAXIMIC | Improved low-pover, CMOS analog switches with latches |
| MX7820LCWP | MAXIMIC | CMOS highspeed 8-bit A/D converter with reference and track/hold function. Error +,-1/2 LSB |
| MAX4253EUB | MAXIMIC | Dual, single-supply operation +2.4V to 5.5V, low-noise, low-distortion, Rail-to-Rail op amp. Gain bandwidth 3MHz, min stable gain 1V/V. |
| MAX6306UK45D1-T | MAXIMIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 4.388(min),4.613(max) Nominal timeout period 1ms. |
| MAX5003C/D | MAXIMIC | High-voltage PWM power-supply controller. |
| MAX100CFR | MAXIMIC | 250Msps, 8-bit ADC with track/hold |
| MAX6321HPUK49DY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| MAX6319LHUK26A-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 1ms |
| MAX366CSA | MAXIMIC | Signal-line circuit protector. |
| MAX6316LUK33DW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.300V, min reset timeout 1.12sec, typ watchdog timeout 6.3ms |
| MAX6250BESA | MAXIMIC | Low-noise, precision, +5V output voltage reference. Max TEMPCO (ppm/C) 7.0. |
| MAX713ESE | MAXIMIC | NiCd/NiMH battery fast-charge controller (negative voltage-slope detection scheme). |
| MAX382CPN | MAXIMIC | Low-voltage, 8-channel multiplexer with latchable inputs. |
| MAX4275ANESA | MAXIMIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 8, 1+ (Rf/Dg) noninverting gain 9, -3dB BW 480kHz. |
