| Teil no | Hersteller | Application |
|---|
| MAX152CPP | MAXIMIC | +3V, 8-bit ADC with 1 micro A power-down |
| MAX4529EUA | MAXIMIC | Low-voltage, bidirectional RF and video switch. |
| MAX106CHC | MAXIMIC | 5V, 600Msps, 8-bit ADC with on-chip 2.2GHz bandwidth track/hold amplifier |
| MAX4281EUK-T | MAXIMIC | Single, open-loop, unity-gain stable amplifier |
| MAX488CUA | MAXIMIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - no. Receiver/driver enable - no. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| MAX6318MHUK33CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.300V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX6241AEPA | MAXIMIC | Low-noise, precision, +4.096V output voltage reference. Max TEMPCO (ppm/C) 3.0. |
| MAX6317HUK42AX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.200V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX4174BAEUK-T | MAXIMIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 10, 1+ (Rf/Dg) noninverting gain 11, -3dB BW 560kHz. |
| MAX869LEEE | MAXIMIC | 2A, current-limited, high-side P-channel switch with thermal shutdown |
| MAX6225BESA | MAXIMIC | Low-noise, precision, +2.5V output voltage reference. Max TEMPCO (ppm/C) 7.0. |
| MAX325ESA | MAXIMIC | Precision, single-supply, SPST analog switch. |
| MAX6318LHUK36CY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.600V min, reset timeout 140ms,typ watchdog timeout 1.6sec |
| MAX6309UK49D2-T | MAXIMIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 4.778(min),5.023(max) Nominal timeout period 20ms. |
| MAX6316LUK26AY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.630V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| MAX4633EPE | MAXIMIC | Fault-protected, high-voltage, dual analog switch (two NO DPST switches). Fault protection +-40V with power off, +-36V with +-15V supplies. |
| MAX690RMJA | MAXIMIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.625V. Active-low reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-4%. Power-fail comparator. Reset window +-75mV |
| MAX320EPA | MAXIMIC | Precision, dual-supply, SPTS analog switch. |
| MXD1000SE60 | MAXIMIC | 5-tap silicon delay line |
| MAX3096ESE | MAXIMIC | +-15kV ESD-Protected, 10Mbps, 5V quad RS-422/RS-485 receiver. |
| MAX6317HUK40DX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 1.12sec, typ watchdog timeout 102ms |
| MAX6355MRUT-T | MAXIMIC | Triple-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.38V (Vcc5) and 2.63V (Vcc3). Active-low open-drain reset. |
| MAX189BCWE | MAXIMIC | +5V, low-power, 12-bit serial ADC. Error(LSB) +-1. |
| MAX6332UR20D1-T | MAXIMIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 2.0V, reset timeout(min) 1ms. |
| ICM7555/D | MAXIMIC | Single general purpose RC timer |
| ICM7218CI/D | MAXIMIC | 8 digit LED display driver |
| MAX489C/D | MAXIMIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| MAX4075AMESA | MAXIMIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 6V/V, noninverting gain 7V/V, -3dB BW 61kHz. |
| MAX4507EAP | MAXIMIC | Fault-protected, high-voltage, signal-line protector |
| MAX668EUB | MAXIMIC | 1.8V to 28V input, RWM step-up controlleer |
