| Teil no | Hersteller | Application |
|---|
| MAX188ACAP | MAXIMIC | Low-power, 8-channel, serial 12-bit ADC. |
| MX581JN | MAXIMIC | High precision 10 volt reference. Error +-30mV. |
| MAX755CPA | MAXIMIC | Negative output, inverting, current-mode PWM regulator. Converts +2.7V to +9V input to adjustable negative output. |
| MAX6319LHUK26B-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 20ms |
| MAX150BCPP | MAXIMIC | CMOS highspeed 8-bit A/D converter with reference and track/hold function. Error +,-1 LSB |
| MAX6352LRUT-T | MAXIMIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.63V (Vcc5) and 2.63V (Vcc3). Active-low open-drain reset. |
| MAX351EPE | MAXIMIC | Precision, quad, SPST analog switch |
| MAX231CWE | MAXIMIC | +5V-powered, multichannel RS-232 driver-receiver. |
| ICM7224IPL | MAXIMIC | 4-1/2 digit counter |
| MAX6317HUK27DY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 2.700V, min reset timeout 1120ms, typ watchdog timeout 1.6sec |
| MAX905ESD | MAXIMIC | Single, high-speed, positive edge-triggered, ECL-compatioble voltage comparator. |
| MAX6320PUK32DY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.200V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| MAX361EJE | MAXIMIC | Precision, quad, SPST analog switch. |
| MAX414BESD | MAXIMIC | Quad, 28MHz, low-noise, low-voltage, precision op amp. |
| MAX6318LHUK32AY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.200V min, reset timeout 1ms, typ watchdog timeout 1.6sec |
| MXD1000C/D20 | MAXIMIC | 5-tap silicon delay line |
| MAX7407ESA | MAXIMIC | 8-th-order, lowpass, elliptic, switched-capacitor filter. Filter response elliptic (r=1.2), operating voltage +3V |
| MAX508BEWP | MAXIMIC | Voltage-output, 12-bit DAC with internal reference. 8+4 data-bus widths. Error +-3/4. |
| MXD1013PD045 | MAXIMIC | 3-in-1 silicon delay line. Output delay 45ns. |
| SI7661CY | MAXIMIC | CMOS voltage converter |
| MAX4566CPE | MAXIMIC | Two dual SPST switches, low-voltage, bidirectional RF/video switch. |
| MAX873BCPA | MAXIMIC | Low-power, low-drift precision voltage reference. 2.5V+-2.5mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC. |
| ICL7135CQI | MAXIMIC | 4-1/2 digit A/D converter with multiplexed BCD outputs |
| MAX6310UK35D3-T | MAXIMIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.413(min),3.588(max). Nominal timeout period 140ms. |
| MAX6320PUK33CZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.300V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX6316LUK35DW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.500V, min reset timeout 1.12sec, typ watchdog timeout 6.3ms |
| MAX562EWI | MAXIMIC | Complete 230kbps, 2.7V to 5.25V serial interface for notebook computers. |
| MAX908ESD | MAXIMIC | Dual, high-speed, ultra low-power, single 4.4V to 5.5V supply operation TTL comparator. |
| MAX145AMJA | MAXIMIC | +2.7 V, low-power, 2-channel, 108 ksps, serial 12-bit ADC. INL(LSB) +-0.5. |
| MAX5181BEEG | MAXIMIC | 10-bit, 40MHz, current/voltage-output DAC. |
