| Teil no | Hersteller | Application |
|---|
| MAX200EPP | MAXIMIC | +5V RS-232 transceiver with 0.1 microF external capacitors |
| MAX3262CAG | MAXIMIC | 1Gbps, high-speed limiting amplifier with catter-free loss-of-signal detection. |
| DG306BWE | MAXIMIC | CMOS dual and quad analog switch. |
| MAX6378XR35-T | MAXIMIC | Ultra-low-power voltage detector, 3.5V |
| MAX7645B/D | MAXIMIC | TTL/CMOS compatible for Vdd = 15V, 12-bit buffered multiplying DAC. Gain error +-3 LSB. |
| MAX971C/D | MAXIMIC | Ultra-low-power, open-drain, single comparator. Internal precision reference 1%. Internal hysteresis yes. |
| DG304BWE | MAXIMIC | CMOS dual and quad analog switch. |
| MXL1178S | MAXIMIC | 17microA max, dual, single-supply precision operational amplifier. |
| MAX813LMJA | MAXIMIC | Low-cost, microprocessor supervisory circuit. Active-low manual-reset input. Active-high reset output. Precision supply-voltage monitor 4.65V. |
| MX7524CD | MAXIMIC | CMOS 8-bit buffered multiplying DAC. TTL/CMOS compatible at +5V. Error +-1/8 LSB |
| MAX6313UK42D2-T | MAXIMIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 4.095(min) 4.305(max).Nominal timeout period 20ms. |
| MAX6316MUK31CY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX6378UR43-T | MAXIMIC | Ultra-low-power voltage detector, 4.3V |
| MX674ASQ | MAXIMIC | Industry standard complete 12-bit A/D converter. 15 microsec. max conversion time. Linearity (LSBs) 1. TEMPCO(ppm/C) 50. |
| MAX4582ESE | MAXIMIC | Low-voltage, CMOS analog multiplexer (two 4-channel). |
| MAX6318LHUK31AW-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.080V min, reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX4663EPE | MAXIMIC | 2.5om, quad, SWPST, CMOS analog switch (two NC and two NO switches). |
| ICL7117C/D | MAXIMIC | 3 1/2 digit A/D converter with display hold |
| MAX6321HPUK36BX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 20ms, watchdog timeout(typ) 102ms |
| MAX1406CWE | MAXIMIC | +-15V, ESD-protected, EMC-compliant, 230kbps, 3-Tx/3-Rx RS-232 IC. |
| MAX122BMRG | MAXIMIC | 500ksps, 12-bit ADCs with track/hold and reference, INL (LSBs) +1 |
| MAX852C/D | MAXIMIC | Low-noise, regulated, negative charge-pump power supplies for GaAsFET bias. 2mVp-p output voltage ripple. Logic-level shutdown mode 1microA max over temp. |
| MX565AKN | MAXIMIC | High speed 12-bit monolithic D/A converter. High stability buried zener 10V reference. Error +-1/4LSB |
| MAX506AMJP | MAXIMIC | Quad 8-bit DAC with Rail-to-Rail voltage outputs. Separate input latches for each of its four DACs. TUE +-1 LSB. |
| MAX794EPE | MAXIMIC | Microprocessor supervisory circuit. Reset threshold programmable. Active-low reset.Active-high reset.Low-line early warning output.Backup-battery switchover.External switch driver.Power-fail comparator.Watchdog input.Manual reset inp. |
| MAX4269ESD | MAXIMIC | Dual, ultra-low-distortion, single-supply, 350MHz op apm with enable. Min gain 2V/V, single-supply operation +4.5V to +8.0V |
| MAX6315US41D1-T | MAXIMIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 4.10V. Reset timeout period(min) 1ms. |
| MAX117CAI | MAXIMIC | 3 V, 400 ksps, 8-channel, 8-bit ADC |
| MAX1240AEPA | MAXIMIC | +2.7V, low-power, 12-bit serial ADCs in 8-pin SO. INL (LSB) +1/2 |
| MAX4202ESA | MAXIMIC | Ultra-high-speed 780MHz -3dB bandwidth, 280MHz 0.1dB gain flatness, low-noise, low-power, open-loop buffer. |
